All Stories

  1. Electrochemical Impedance Spectroscopy (EIS) Evaluation of Hydroxyapatite-Coated Magnesium in Different Corrosion Media

    Article • Solid State Phenomena, August 2018, Trans Tech Publications

    Mohd Amin Farhan Zaludin, Dr Mohd Nazree bin Derman

  2. Effect of TiO 2 additions on Sn-0.7Cu-0.05Ni lead-free composite solder

    Article • Microelectronics Reliability, October 2016, Elsevier

    Dr Mohd Nazree bin Derman

  3. Isothermal Aging Affect to the Growth of Sn-Cu-Ni-1 wt.% TiO2 Composite Solder Paste

    Article • Key Engineering Materials, July 2016, Trans Tech Publications

    Miss Rita Mohd Said, Dr Mohd Nazree bin Derman

  4. Wettability and Shear Strength of Sn-Cu-Ni-xSi3N4 Composite Solder

    Article • Key Engineering Materials, July 2016, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  5. Improvement of Sn-0.7Cu Lead Free Solder Joints on Shear Strength with Addition of Titanium Oxide (TiO2) Particles

    Article • Materials Science Forum, May 2016, Trans Tech Publications

    Miss Rita Mohd Said, Dr Mohd Nazree bin Derman

  6. Influence of Activated Carbon Particles on Intermetallic Compound Growth Mechanism in Sn-Cu-Ni Composite Solder

    Article • MATEC Web of Conferences, January 2016, EDP Sciences

    Dr Mohd Nazree bin Derman

  7. An Investigation of TiO2Addition on Microstructure Evolution of Sn-Cu-Ni Solder Paste Composite

    Article • MATEC Web of Conferences, January 2016, EDP Sciences

    Dr Mohd Nazree bin Derman

  8. Highly Response and Sensitivity Chitosan-Polyvinyl alcohol Based Hexanal Sensors

    Article • MATEC Web of Conferences, January 2016, EDP Sciences

    Dr Mohd Nazree bin Derman

  9. A brief review of calcium phosphate conversion coating on magnesium and its alloys

    Article • January 2016, American Institute of Physics

    Dr Mohd Nazree bin Derman

  10. Hexanal Gas Detection Using Chitosan Biopolymer as Sensing Material at Room Temperature

    Article • Journal of Sensors, January 2016, Hindawi Publishing Corporation

    Dr Mohd Nazree bin Derman

  11. Nitric acid treated multi-walled carbon nanotubes optimized by Taguchi method

    Article • January 2016, American Institute of Physics

    Dr Mohd Nazree bin Derman

  12. Fast Fourier Transform Analysis of Images of Scanning Electron Microscope of Porous Anodic Alumina

    Article • Advanced Materials Research, June 2015, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  13. Oxide Dissolution Treatment of Porous Anodic Alumina

    Article • Advanced Materials Research, June 2015, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  14. Synthesis of Porous Anodic Alumina on Aluminium Manganese Alloys

    Article • Advanced Materials Research, June 2015, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  15. The Effect of Micron-Size Silicon Additions on Microstructure, Microhardness and Thermal Properties of Sn-Cu-Ni Solder Alloy

    Article • Materials Science Forum, June 2015, Trans Tech Publications

    Miss Rita Mohd Said, Dr Mohd Nazree bin Derman

  16. Effect of Si3N4 Addition on the Properties of Sn-1.0Ag-0.7Cu Solder Alloy

    Article • Materials Science Forum, June 2015, Trans Tech Publications

    Miss Rita Mohd Said, Dr Mohd Nazree bin Derman

  17. Fabrication and Characterization of Different Ca Content in Mg-Ca Composite Using Powder Metallurgy Technique

    Article • Materials Science Forum, June 2015, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  18. Ammonia Gas Sensor Based on Chitosan Biopolymer

    Article • Materials Science Forum, June 2015, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  19. Synthesis of Nanoporous Zinc Oxide by Anodizing of Zinc in Distilled Water

    Article • Applied Mechanics and Materials, April 2015, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  20. The Effect of Microwave Sintering Time to PM Aluminum Alloys

    Article • Applied Mechanics and Materials, April 2015, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  21. Influence of Silicon Nitride (Si3N4) Addition on Microstructure, Mechanical and Thermal Properties of Sn-0.7Cu Lead-Free Solder

    Article • Applied Mechanics and Materials, April 2015, Trans Tech Publications

    Miss Rita Mohd Said, Dr Mohd Nazree bin Derman

  22. Microstructure and Mechanical Properties of Sn-1.0Ag-0.7Cu (SAC107) Lead-Free Solder Reinforced Silicon Nitride (Si3N4) Particles

    Article • Applied Mechanics and Materials, April 2015, Trans Tech Publications

    Miss Rita Mohd Said, Dr Mohd Nazree bin Derman

  23. Roselle Blend Film Sensor (RBFS) for Detecting Fertilizer Concentration of Grape Tree

    Article • Applied Mechanics and Materials, April 2015, Trans Tech Publications

    DR KHAIREL RAFEZI AHMAD, Dr Mohd Nazree bin Derman

  24. Effect of Aging Temperature to the Corrosion Behaviour of 5D86 Aluminum Alloy

    Article • Applied Mechanics and Materials, April 2015, Trans Tech Publications

    Juyana a wahab, Dr Mohd Nazree bin Derman

  25. Effect of Sintering Temperature on Different Ca Content in Mg-Ca Composite Using Powder Metallurgy Technique

    Article • Applied Mechanics and Materials, April 2015, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  26. Spinach Ferredoxin (Fdx) as an Organic Material to Improve Optical Band Gap of Chitosan (Cs) Biofilm

    Article • Applied Mechanics and Materials, April 2015, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  27. A Study of PM Mg-HAP Composite: Corrosion and Microstructural Evaluation

    Article • Applied Mechanics and Materials, April 2015, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  28. Role of Metals Content in Spinach in Enhancing the Conductivity and Optical Band Gap of Chitosan Films

    Article • Advances in Materials Science and Engineering, January 2015, Hindawi Publishing Corporation

    Dr Mohd Nazree bin Derman

  29. Rapid and sensitive E-Coli DNA detection by titanium dioxide nanoparticles

    Article • December 2014, Institute of Electrical & Electronics Engineers (IEEE)

    Dr Mohd Nazree bin Derman

  30. The Effect of Silicon Nitride Addition on Microstructure and Microhardness of SN100C Solder Alloy Using Powder Metallurgy

    Article • Materials Science Forum, August 2014, Trans Tech Publications

    Miss Rita Mohd Said, Dr Mohd Nazree bin Derman

  31. Effect of TiO2 Reinforcement on Microstructure and Microhardness of Low-Silver SAC107 Lead-Free Solder Composite Solder

    Article • Materials Science Forum, August 2014, Trans Tech Publications

    Miss Rita Mohd Said, Dr Mohd Nazree bin Derman

  32. Effects of ethanol in oxalic acid on the synthesis of porous anodic alumina

    Article • August 2014, Institute of Electrical & Electronics Engineers (IEEE)

    Dr Mohd Nazree bin Derman

  33. Synthesis of zinc oxide thin film by anodizing

    Article • August 2014, Institute of Electrical & Electronics Engineers (IEEE)

    Dr Mohd Nazree bin Derman

  34. The effect of metallic oxide deposition on the electrochemical behaviour of Al-Zn-Mg-Sn alloy in natural tropical seawater

    Article • IOP Conference Series Materials Science and Engineering, June 2014, Institute of Physics Publishing

    Dr Mohd Nazree bin Derman

  35. Effect of Anodizing Voltage on the Formation of Porous Anodic Alumina on Al-0.5wt% Mn Alloys

    Article • Advanced Materials Research, April 2014, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  36. Serine Sensor Based on Graphene Sheet Congo-Red Molecular Imprinted Polymer (GSCR-MIP) Organic Thin Film Transistor (OTFT)

    Article • Advanced Materials Research, April 2014, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  37. MICROSTRUCTURE AND IN-VITRO TEST BIOACTIVITY BEHAVIOR OF Co-Cr-Mo (F-75)/HYDROXYAPATITE IN PHOSPHATE BUFFERED SALINE SOLUTION

    Article • Acta Metallurgica Slovaca, January 2014, Technical University of Kosice, Faculty of Manfacturing Technologies

    Dr Mohd Nazree bin Derman

  38. Characteristic and Corrosion Studies of Rare Earth (Ree) Based Anodizing on AZ91D Magnesium Alloy

    Article • Advanced Materials Research, January 2014, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  39. Characterization of PM Fe-Cr-Y2O3 Composites Prepared by Microwave Sintering Technology

    Article • Advanced Materials Research, January 2014, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  40. Surface Morphology and Corrosion Behavior of Electrolytic Coatings in Different Aqueous Solutions

    Article • Key Engineering Materials, December 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  41. Characteristic and Corrosion Studies of Rare Earth (REE) Based Anodizing on AZ91D Magnesium Alloy

    Article • Key Engineering Materials, December 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  42. Comparison Study in Consolidation of Yttria Reinforced Iron-Chromium Composites Using Conventional and Microwave Sintering Technique

    Article • Key Engineering Materials, December 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  43. Cu-SiCp Composites as Advanced Electronic Packaging Materials

    Article • Key Engineering Materials, December 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  44. Different Concentration of Al(NO3)3 in ZrO2/Al2O3 Double Layer Coating Steel Prepared by Electrolytic Method

    Article • Key Engineering Materials, December 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  45. Thermal Expansion Behavior of the Electroless Copper Coated Cu-SiCp Composites Fabricated via the Conventional Powder Metallurgical Technique

    Article • Key Engineering Materials, December 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  46. Using Gibbs Standard State Free Energy And A Power Regulating Device To Predict And Control The Fabrication Of Nanoporous Alumina

    Article • Advanced Materials Letters, December 2013, VBRI Press

    Dr Mohd Nazree bin Derman

  47. Effect of Anodizing Voltage on the Morphology and Growth Kinetics of Porous Anodic Alumina on Al-0.5 wt% Mn Alloys

    Article • Advanced Materials Research, November 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  48. The Thermal Expansion Behaviors of Cu-SiCp Composites

    Article • Advanced Materials Research, September 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  49. Corrosion Behaviour of Anodised Powder Metallurgy Aluminium-Magnesium Composites

    Article • Advanced Materials Research, September 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  50. A Study on the Effect of Modified Electrolyte to the Formation of AAO Membrane in Anodising Process

    Article • Advanced Materials Research, September 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  51. Corrosion Behavior of Al-Cu-Ni-Y Alloys

    Article • Advanced Materials Research, September 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  52. Effect of Anodizing Voltage on the Growth Kinetics of Porous Anodic Alumina on Al-0.5 wt% Mn Alloys

    Article • Advanced Materials Research, September 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  53. Effect of Deposition Time on Properties of ZrO2 Coating Prepared Using Electrolytic Method

    Article • Advanced Materials Research, September 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  54. Electrochemical Corrosion Behaviour of Mg-(Ca,Mn) Sacrificial Anodes

    Article • Advanced Materials Research, September 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  55. Electrochemical Measurement of PBS Using Cyclic Voltammetry and AAO Fabricated at Ambient Temperature and Low Potential

    Article • Advanced Materials Research, September 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  56. Organic Dye Degradation with TiO2 Catalyst/AAO Template in the Presence of H2O2

    Article • Advanced Materials Research, September 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  57. Overview of Pathogenic Micro-Organisms Destruction in Contaminated Water by Oxide Photocatalysis

    Article • Advanced Materials Research, September 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  58. Synthesis and Characterization of Electroless Copper Coated SiC Particles

    Article • Advanced Materials Research, September 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  59. Effect of Heat Treatment on Microstructure and Corrosion Behavior of Az91d Magnesium Alloy

    Article • Advanced Materials Research, April 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  60. Microstructure and Properties of Heat-Treated 440C Martensitic Stainless Steel

    Article • Defect and Diffusion Forum, February 2013, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  61. Effect of Temperature of Oxalic Acid on the Fabrication of Porous Anodic Alumina from Al-Mn Alloys

    Article • Journal of Nanomaterials, January 2013, Hindawi Publishing Corporation

    Dr Mohd Nazree bin Derman

  62. Effect of Electrolyte Concentration on the Growth of Porous Anodic Aluminium Oxide (AAO) on Al-Mn Alloys

    Article • Advanced Materials Research, December 2012, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  63. Room Temperature Anodization Of Aluminum And The Effect Of The Electrochemical Cell In The Formation Of Porous Alumina Films From Acid And Alkaline Electrolytes

    Article • Advanced Materials Letters, September 2012, VBRI Press

    Dr Mohd Nazree bin Derman

  64. A simple one-step anodising method for the synthesis of ordered porous anodic alumina

    Article • Journal of Experimental Nanoscience, July 2012, Taylor & Francis

    Dr Mohd Nazree bin Derman

  65. Microstructural Characterization of ZrO2 Layer Coating on Martensitic Stainless Steel

    Article • Applied Mechanics and Materials, April 2012, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  66. Effect of Manganese Content on the Fabrication of Porous Anodic Alumina

    Article • Journal of Nanomaterials, January 2012, Hindawi Publishing Corporation

    Dr Mohd Nazree bin Derman

  67. Characterization of Porous Anodic Aluminium Oxide Film on Aluminium Templates Formed in Anodizing Process

    Article • Advanced Materials Research, December 2010, Trans Tech Publications

    Dr Mohd Nazree bin Derman

  68. Growth of Cu-Zn5 and Cu5Zn8 Intermetallic Compounds in the Sn-9Zn/Cu Joint during Liquid State Aging

    Article • Advanced Materials Research, December 2010, Trans Tech Publications

    Dr Mohd Nazree bin Derman