All Stories

  1. Microstructure and mechanical properties of a martensitic stainless steel (0.2%C–12%Cr) after quenching and partitioning (Q&P) process

    Article • Journal of Materials Research and Technology, May 2023, Elsevier

    PhD - Metallurgy and Materials Jan Vatavuk

  2. Influence of Thermal Oxidation on the Creep Behavior of Ti-6Al-4V Alloy

    Article • Materials Research, January 2023, FapUNIFESP (SciELO)

    PhD - Metallurgy and Materials Jan Vatavuk

  3. Relations of Compressive Residual Stress on Prestressed Surfaces Submitted to the Stress Shot Peening Process in EN 47 Spring Steel

    Article • Materials Research, January 2023, FapUNIFESP (SciELO)

    PhD - Metallurgy and Materials Jan Vatavuk

  4. Effect of Friction Stir Welding on Microstructure and Mechanical Properties of uns C19400 Alloy Plates

    Article • Materials Research, January 2023, FapUNIFESP (SciELO)

    PhD - Metallurgy and Materials Jan Vatavuk

  5. Engenharia, Gestão e Inovação – Volume 6

    Article • January 2022, Editora Poisson

    PhD - Metallurgy and Materials Jan Vatavuk

  6. Effect of Mg and Cu on microstructure, hardness and wear on functionally graded Al–19Si alloy prepared by centrifugal casting

    Article • Journal of Materials Research and Technology, November 2020, Elsevier

    PhD - Metallurgy and Materials Jan Vatavuk

  7. Effect of Copper and Magnesium on the Microstructure of Centrifugally Cast Al-19%Si Alloys

    Article • Materials Science Forum, September 2018, Trans Tech Publications

    PhD - Metallurgy and Materials Jan Vatavuk, Dr Antonio A Couto, Chester Contatori

  8. TÊMPERA DE AÇO SAE 1045 UTILIZANDO DIFERENTES MEIOS DE RESFRIAMENTO

    Article • September 2017, Editora Edgard Blucher, Ltda.

    PhD - Metallurgy and Materials Jan Vatavuk

  9. Nitriding Process Characterization of Cold Worked AISI 304 and 316 Austenitic Stainless Steels

    Article • Journal of Metallurgy, January 2017, Hindawi Publishing Corporation

    PhD - Metallurgy and Materials Jan Vatavuk

  10. Comparative Impact Behavior of High-C Steel After Conventional Quenching, Tempering, and Austempering

    Article • Materials Performance and Characterization, August 2016, ASTM International

    Dr. George E Totten, Lauralice de Campos Franceschini Canale, PhD - Metallurgy and Materials Jan Vatavuk

  11. High Temperature Mechanical Behavior of Plasma-Nitrided Inconel 625 Superalloy

    Article • July 2016, Springer Science + Business Media

    PhD - Metallurgy and Materials Jan Vatavuk

  12. Effect of chemical banding on the local hardenability in AISI 4340 steel bar

    Article • Engineering Failure Analysis, July 2015, Elsevier

    PhD - Metallurgy and Materials Jan Vatavuk

  13. Study of the Utilization of Polyamide Composite with Fiberglass Reinforcement in Automotive Engine Mounts

    Article • January 2015, Springer Science + Business Media

    PhD - Metallurgy and Materials Jan Vatavuk

  14. Problems Associated with Heat Treating

    Article • September 2014, ASM International

    PhD - Metallurgy and Materials Jan Vatavuk

  15. The Metallographic Technical Preparation Influence on the Zinc Hot Dip Deposited Layer Morphology

    Article • Materials Science Forum, September 2014, Trans Tech Publications

    SONIA FALDINI, PhD - Metallurgy and Materials Jan Vatavuk

  16. The Effect of Strain Hardening in Stainless Steels Submitted to Nitriding Treatment

    Article • January 2014, Springer Science + Business Media

    PhD - Metallurgy and Materials Jan Vatavuk

  17. Introduction to Steel Heat Treatment

    Article • January 2014, Elsevier

    PhD - Metallurgy and Materials Jan Vatavuk

  18. Development and Application in Dampers and Gas Springs of a Hydraulic Fluid with Biodegradable Properties and Strong Thermochemical Resistance Based on Innovative Molecular Structure

    Article • October 2013, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  19. Martempering of Steels

    Article • August 2013, ASM International

    PhD - Metallurgy and Materials Jan Vatavuk

  20. Tempering of Steels

    Article • August 2013, ASM International

    PhD - Metallurgy and Materials Jan Vatavuk

  21. Design of Wear-Resistant Coatings for Engine Components

    Article • January 2013, Springer Science + Business Media

    PhD - Metallurgy and Materials Jan Vatavuk

  22. Failure Analysis of an Automotive Component (Cardan Yoke) by Scanning Electron Microscopy

    Article • Defect and Diffusion Forum, April 2012, Trans Tech Publications

    Doctor Danieli DAP Reis Reis , PhD - Metallurgy and Materials Jan Vatavuk

  23. Nitriding effect on fatigue resistance of grey and nodular cast irons

    Article • International Heat Treatment and Surface Engineering, March 2012, Taylor & Francis

    Lauralice de Campos Franceschini Canale, PhD - Metallurgy and Materials Jan Vatavuk

  24. Computational Simulation in Centrifugal Casted Aluminum–Silicon Engine Cylinder Liner

    Article • January 2012, Springer Science + Business Media

    PhD - Metallurgy and Materials Jan Vatavuk

  25. The Modified Martempering and its Effect on the Impact Toughness of a Cold Work Tool Steel

    Article • October 2011, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  26. The Effect of Core Microstructural Stability associated with the transformation occurred in the Carburized Surface on Residual Stress Evolution during Tempering

    Article • October 2010, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  27. The Interaction of Piston-Ring-Cylinder on Flex Fueled Engines

    Article • October 2010, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  28. Piston Ring Tribological Challenges on the Next Generation of Flex-fuel Engines

    Article • SAE International Journal of Engines, May 2010, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  29. Review of Prior Studies of Fuel Effects on Vehicle Emissions

    Article • SAE International Journal of Fuels and Lubricants, April 2009, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  30. The Effect of Core and Carburized Surface Microstructural Stability on Residual Stress Evolution during Tempering

    Article • Journal of ASTM International, January 2009, ASTM International

    PhD - Metallurgy and Materials Jan Vatavuk

  31. Steel Failures due to Tempering and Isothermal Heat Treatment

    Article • September 2008, ASM International

    PhD - Metallurgy and Materials Jan Vatavuk

  32. The effect of nitriding on the toughness and bending resistance of tool steels

    Article • International Journal of Microstructure and Materials Properties, January 2008, Inderscience Publishers

    Dr. George E Totten, PhD - Metallurgy and Materials Jan Vatavuk

  33. Performance of a Test Procedure for Heavy Duty Diesel Engines in Order to Mimic Accelerated Conditions of Liners Deterioration.

    Article • November 2006, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  34. Preliminary study to data adequation to use engineering tooling in perlitic matrix gray cast iron

    Article • November 2006, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  35. Evaluation of Mechanical Properties and Microstructure of a High Carbon-Vanadium Tool Steel Produced by Powder Metallurgy

    Article • Materials Science Forum, November 2006, Trans Tech Publications

    PhD - Metallurgy and Materials Jan Vatavuk

  36. Modulus of Rupture Evaluation on P/M Cold Worked Tool Steels Submitted to Gas Nitriding

    Article • Materials Science Forum, February 2003, Trans Tech Publications

    PhD - Metallurgy and Materials Jan Vatavuk

  37. Study of Sea Transportation Effects on Corrosion of Cast Iron Cylinder Liners

    Article • March 2001, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  38. A Comparative Study Between Salt Bath and Plasma Nitrocarburizing Processes for Application in Piston Rods

    Article • December 2000, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  39. Solid State Alloying by Plasma Nitriding and Diffusion Annealing Treatment for Austenitic Stainless Steel

    Article • Materials Science Forum, January 1999, Trans Tech Publications

    PhD - Metallurgy and Materials Jan Vatavuk

  40. Effect of the Nitriding Process on Impact Resistance of Austempered Cast Irons and Quenched and Tempered Ones

    Article • December 1997, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  41. Bead Weld Cold Plastic Deformation Effects on AISI 409 Ferritic Stainless Steel, Ti and Nb Stabilized

    Article • October 1995, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  42. The Effect of the Addition of Hard Particles on the Wear of Liner and Ring Materials Running with High Sulfur Fuel

    Article • February 1995, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  43. Nitrited Steel Piston Rings for Internal Combustion Engines

    Article • November 1994, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  44. Nittred Gray Cast Iron Piston Rings

    Article • November 1994, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  45. Development Of Nitrided Oil Control Rings With Contoured Rails

    Article • October 1993, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  46. Improvement Of Cylinder Liner Materials Wear Resistance.

    Article • October 1993, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  47. New Concept For Wear Resistant Coatings For Piston Rings.

    Article • October 1993, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  48. Configurations and Materials of Oil Control Rings to Meet the New Internal Combustion Engines Requirements

    Article • November 1992, SAE International

    PhD - Metallurgy and Materials Jan Vatavuk

  49. Wear-resistant nodular iron for automotive piston rings

    Article • JOM, January 1992, Springer Science + Business Media

    PhD - Metallurgy and Materials Jan Vatavuk